Velocity analysis and statics corrections exercises

From SEG Wiki
Revision as of 10:34, 19 September 2014 by Ageary (talk | contribs) (Figures and equations: fixed eqn)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Seismic Data Analysis
Series Investigations in Geophysics
Author Öz Yilmaz
ISBN ISBN 978-1-56080-094-1
Store SEG Online Store

Exercise 3-1. Why does salt have anomalously high velocity (4.5 to 5.5 km/s)?

Exercise 3-2. Measure the traveltimes corresponding to offset values of 1 and 3 km in Figure 3.1-2. Then compute the velocity above the reflector and verify that it is 2264 m/s. Note that the zero-offset trace is not recorded; therefore, t0 normally is not a known quantity.

Exercise 3-3. The CMP gather in Figure 3.1-5a contains a hyperbola. Following NMO corrections and using 2000 (Figure 3.1-5c) and 2500 m/s (Figure 3.1-5d) velocities, are the traveltime trajectories hyperbolic?

Exercise 3-4. Make velocity picks from the velocity panels in Figures 3.2-4, 3.2-5, 3.2-6, and 3.2-7.

Exercise 3-5. Make velocity picks from the CVS panel in Figure 3.E-1.

Exercise 3-6. Consider two intersecting lines. Would you expect that velocity analyses at the intersection point yield the same velocity function?

Exercise 3-7. Which is correct: velocity analysis from datum or velocity analysis from surface?

Exercise 3-8. Fill the missing elements in the following table. Average velocity vavg, which relates vertical traveltime to depth in a horizontally layered medium, is defined as where Δti = Δzi / vi, Δzi = layer thickness and vi = interval velocity. The rms velocity is given by equation (4).

Layer Thickness, m Interval Velocity, m/s RMS Velocity, m/s Average Velocity, m/s
200 2,000    
300 3,000    
400 4,000    
350 3,500    
500 5,000    

Exercise 3-9. Explain why the velocity for horizon A in Figure 3.2-34 behaves as shown in the HVA display below the salt dome S.

Exercise 3-10. Suppose you want to fit a set of observed traveltimes to a parabola of the form t = a + bx + cx2. The tabulated input values are given below.

i xi Observed
1 0 0.4
2 1 1.1
3 2 3.5
4 3 7.9
5 4 14.4

Set up the least-squares problem and solve for a, b, and c. You will have five equations and three unknowns.

Exercise 3-11. Solve the system

by the Gauss-Seidel iterative method. Verify the results by solving these equations by the method of substitution to obtain the correct solution: x1 = 2 and x2 = 0.5.

Exercise 3-12. Solve the system

by the Gauss-Seidel iterative method. Note that this is the same problem as in Exercise 3-11, except that the order of the equations is reversed. The solution should be the same. You will find that the solution cannot be obtained because the process of iteration will not converge. This demonstrates the importance of ordering the equations when solving by the Gauss-Seidel method.

Exercise 3-13. Write equation (37a) for i = 1, 2, 3, and j = 1, 2, 3. You will find that there are six unknowns, but five independent equations.

Exercise 3-14. Can you use refraction-based statics techniques in permafrost areas?

Exercise 3-15. Which of the following adversely affects the quality of velocity spectrum — long-wavelength or short-wavelength (less than a cable length) statics anomalies?

Exercise 3-16. In what way does inside muting of a CMP gather affect the velocity spectrum?

Figures and equations




See also

External links

find literature about
Velocity analysis and statics corrections exercises
SEG button search.png Datapages button.png GeoScienceWorld button.png OnePetro button.png Schlumberger button.png Google button.png AGI button.png